lemonadess
Banned
Lưu ý đây chỉ là hướng dẫn nhằm mục đích quảng cáo là chính
Các bạn có làm thì chỉ tháo tới đây thôi. Gọi là vui đùa với phần cứng 1 tí. Đừng ham hố tháo thêm. Đỡ không kịp đâu.
Về việc tháo máy, có 1 khuyến cáo như sau:
Tuyệt đối không tháo máy nếu bạn không fải là người "dày dạn" kinh nghiệm. Bởi vì tháo thì dễ, tới hồi lắp vào tự nhiên pó tay, mà mình là 1 ví dụ. Còn khi tháo, có thể bạn sẽ làm đứt dây nào đó mà không biết. Hoặc đứt bảng mạch này nọ. Và rồi không biết đó là cái gì để sửa.
Những ai có ý đồ xem modchip của máy thì có lẽ nên bỏ ngay. Bởi lạng quạng là hư hết, coi chừng fix không được. Mình chỉ mới bị lỗi nuốt đĩa khi tháo thôi, cũng còn hên.
Bài viết ở đây copy từ website nước ngoài. Trước tiên post tiếng Anh trước, bởi vì chưa có thời gian dịch. :em17: Nhưng mà nhìn cũng dễ hiểu lắm mà.
You will only need two tools to take apart the Wii. The first is a small Phillips screw driver, which should be easy to locate. The second tool you will need is a Triwing driver.
To disassemble:
Còn phần lắp vào nữa. Sẽ cập nhật sau . Nhưng cứ làm ngược lại mấy bước trên là ok rồi.
Bảo đảm với mọi người rằng mình đã tháo tới giai đoạn như trong hình vẽ. Chỗ 2 ô đen như processor ấy hình như có gắn modchip. Halo dán băng keo trắng lại. Mình táy máy tháo ra, và đã đem đi sửa đấy
Các bạn có làm thì chỉ tháo tới đây thôi. Gọi là vui đùa với phần cứng 1 tí. Đừng ham hố tháo thêm. Đỡ không kịp đâu.
Về việc tháo máy, có 1 khuyến cáo như sau:
Tuyệt đối không tháo máy nếu bạn không fải là người "dày dạn" kinh nghiệm. Bởi vì tháo thì dễ, tới hồi lắp vào tự nhiên pó tay, mà mình là 1 ví dụ. Còn khi tháo, có thể bạn sẽ làm đứt dây nào đó mà không biết. Hoặc đứt bảng mạch này nọ. Và rồi không biết đó là cái gì để sửa.
Những ai có ý đồ xem modchip của máy thì có lẽ nên bỏ ngay. Bởi lạng quạng là hư hết, coi chừng fix không được. Mình chỉ mới bị lỗi nuốt đĩa khi tháo thôi, cũng còn hên.
Bài viết ở đây copy từ website nước ngoài. Trước tiên post tiếng Anh trước, bởi vì chưa có thời gian dịch. :em17: Nhưng mà nhìn cũng dễ hiểu lắm mà.
You will only need two tools to take apart the Wii. The first is a small Phillips screw driver, which should be easy to locate. The second tool you will need is a Triwing driver.
To disassemble:
- Flip the device upside down and remove the small silver Phillips screw. Once out, remove the battery tray from the console.
- Next remove the rubber foot directly above this battery tray. Also remove the three square white stickers from the bottom of the Wii. The rubber foot and the sticker are covering hidden screws. Figure 3 provides a shot of where these screws are located. NOTE
Hiding screws under stickers and rubber pads is a common method used by electronics manufactures to help increase the aesthetics of their devices, as well as prevent people from easily locating screws and taking apart their products. - Unscrew the two Triwing screws and three Phillips screws from the bottom of the Wii.
- Figure 3
- Bottom Screws
- Flip the Wii over onto its right side. Locate and remove the two rear rubber feet and the two rectangle stickers near the faceplate.
- Remove the two silver Triwing screws in the holes and remove the two black Triwing screws on the faceplate (Figure 4).
- Figure 4
Left side screw locations - Flip the Wii upright and carefully remove the two socket covers. They come right out with a little wiggling.
- Remove the three black Phillips screws from the black plate (Figure 5). Note the one closest to the faceplate is the longest and will need to go back into that hole when putting the Wii back together.
- Figure 5
Top black plate screw locations - With the screws removed, carefully pull off the faceplate of the front of the Wii. You will need to disconnect the red/black wire plug from the Wii to remove the faceplate completely. Figure 6 shows what is hiding under the faceplate.
- Figure 6
Under the Wii faceplate - Remove black plate from memory/controller socket area.
- Remove two silver Phillips and two silver Triwing screws from memory/controller socket area (Figure 7).
- Figure 7
Topside screw locations - Lay the Wii on left side (with the ATI and Nintendo logo facing you) and slowly work the right side cover of the console off the device. This will take a little bit of force. If something appears to be stuck, double check to ensure you removed all the screws.
- Locate and remove four screws holding DVD reader in place. Two are located in plain site in the middle of the unit. Two are located near the front of the Wii inside the DVD unit (Figure 8).
- Figure 8
The insides of the Wii - Slowly tilt the DVD player upward toward top of Wii. There are two wires that need to be disconnected before you can safely remove the DVD unit. One is a plug type of connector that only requires a little tug. The other is a circuit strip connector that requires you to lift the brown catch, which will release the pressure holding the strip in place (Figure 9). Do not break this!
Còn phần lắp vào nữa. Sẽ cập nhật sau . Nhưng cứ làm ngược lại mấy bước trên là ok rồi.
Bảo đảm với mọi người rằng mình đã tháo tới giai đoạn như trong hình vẽ. Chỗ 2 ô đen như processor ấy hình như có gắn modchip. Halo dán băng keo trắng lại. Mình táy máy tháo ra, và đã đem đi sửa đấy